Mechanical Presses

Can’t reset emergency stop
01.B.D.C sensor doesn’t work.
 Check the electrical contact point. If it is OK, replace the sensor.
02.Mis-feed sensor doesn’t work.
 Check the electrical contact point. If it is OK, replace the sensor.
03.O.L.P. solenoid stuck.
 Check whether something inside to block the solenoid. Clean it or replace it.
04.E.stop circuit wire loosened.
 Check the circuit and fasten it.
05.Over heat to stop main motor.
 Check the current setting on thermal relay. If the setting is correct, reset the relay. Or adjust it.
06.Leakage in O.L.P.
 Check the packing seal. If any damage found, replace it.
07.Pre-set counter broken.
 Check the electrical contact point and clean it.
08.Oil level sensor broken.
 Replace it.
09.Wrong grease used and error message occurs to stop operation.
 Check the specification of grease, if wrong replace it.
10.Converter self-protect.
 Check the temperature of converter and the ventilation. Replace the fan if need. Check the indicating light and follow the instruction manual to repair it.
11.Air pressure switch actuated by vibration.
 Check the air pressure in tank. If pressure is OK, replace the pressure switch.
12.Run out of battery.
 Replace a new battery.
13.Stuck release pressure switch broken.
 Check the switch. Replace it if need.
14.Air pressure switch setting loosened.
 Fasten it.
Abnormality in Slide
01.Cap above ball screw loosened.
 Clean inside and fasten all bolts.
02.Air pressure in counterbalance.
 Based on the pressure curve to adjust it.
03.O.L.P. solenoid stuck
 Check it and connect it.
04.Parts loosened.
 Replace all damage parts.
05.Locking pin loosened.
 Fasten it.
Oil leakage
01.Oil pipe loosened in con-rod.
 Fasten the pipe.
02.Oil is over added in gear box.
 Drain the excess oil till the suitable oil level.
03.Packing seal in the O.L.P. broken.
 Replace it.
04.Packing seal ageing and broken.
 Replace it.
05.Leakage in O.L.P. pressure switch.
 Replace it.
06.Oil splash in Clutch/Brake air exhaust.
 Check the pneumatic lubrication oil amount.
07.Oil splash in slide gib.
 Check the lub. Oil amount and adjust it. Also, check the oil pan position.
Abnormality in Slide adjust
01.Motor stop.
 Check thermal relay and reset it.
02.Air pressure too high.
 Adjust the air pressure based on the balance chart.
03.Die height limit circuit broken.
 Check the upper and lower limit circuit. Re-wire it if need.
04.Motor wire loosened or short circuit.
 It could cause motor and contactor burning. Check wire condition.
05.Switch broken.
 Replace it.
06.Connector of solenoid broken.
 Re-wire it.
07.Brake lining broken.
 Replace lining.
08.Wiring in T-stand broken.
 Re-wire it.
09.Wrom gear and wheel wear off.
 Replace all.
10.Slide locking cylinder stuck.
 Check cylinder and clean it.
11.Air pressure too high in counterbalance.
 Adjust to suitable air pressurebased on the pressure chart.
12.Upper and lower limit can’t work properly.
 Check the limit setting and wiring condition.
Oil leakage
01.Oil pipe loosened in con-rod.
 Fasten the pipe.
02.Oil is over added in gear box.
 Drain the excess oil till the suitable oil level.
03.Packing seal in the O.L.P. broken.
 Replace it.
04.Packing seal ageing and broken.
 Replace it.
05.Leakage in O.L.P. pressure switch.
 Replace it.
06.Oil splash in Clutch/Brake air exhaust.
 Check the pneumatic lubrication oil amount.
07.Oil splash in slide gib.
 Check the lub. Oil amount and adjust it. Also, check the oil pan position.

 

Abnormality in lubrication
01.Wrong oil chosen.
 Based on the instruction plate to choose the right one.
02.Stuck in piping.
 Blow the pipe with high air pressure.
03.Motor doesn’t work.
 Power fail or something stuck. Detach motor and pump to judge the function of either one.
04.Air in oil pipe.
 Expel air by drain all oil in pipe and refill it.
05.Dirty grease or air inside.
 Wrong way to pump-in grease. Grease should pump-in via grease bead with grease gun.
06.Grease packing deformed.
 Rearrange cap or replace packing.
07.Pump cam stuck.
 Something dirty inside? Clean it and refill it.
08.Oil leak or mud stuck.
 Fasten fitting and clean it.
09.Motor out of order in grease pump.
 Replace it.
10.Fuse burn.
 Replace it.
11.Lubricant distribotor.
 Check all the lubricant outlets. Replace it if need.
Abnormality in O.L.P
01.Keep on pumping because of high pressure.
 Adjust the right pressure.
02.Pump broken.
 Replace it.
03.Keep on pumping because of something inside.
 Disassemble and clean it.
04.Emergency stop because of low pressure.
 Adjust the right pressure.
05.Wrong oil chosen.
 Based on the instruction plate to choose the right one.
06.Solenoid in O.L.P. broken.
 Replace it.
07.Ol tank leaks.
 Any crack found? Or screw loosened?
08.Packing seal broken.
 Replace it.
Abnormality in Clutch/Brake
01.Noise in Brake.
 Check the pneumatic lubrication oil amount. Be sure piston move smoothly.
02.Noise in belt.
 Check the tension of belt.
03.Speed too high. Smell something burn.
 Reduce speed. Or ventilation for heat sink.
04.Stroke of brake too big.
 Adjust the clearance by taking out the shims. Or replace the lining.
05.T.D.C stop fail.
 Check the clearance of brake. Replace the lining if need.
06.Abnormality in circuit.
 Check the indicating light and follow the instruction to solve the problem.